Where is the truck switch on a 1992 firebird?
by the steering wheel
2 people found this useful
First, remove the lower dashboard panel in order to get at the switch. There are four Philips screws and one bolt that secures this panel. Then remove the two nuts and three b…olts securing the steering column to the dash frame. This makes it easy to get at the switch. Remove the cover around the ignition switch. The front part is the key and lock tumbler, and the bottom is the electrical switch part that is not disturbed by this process. Take care not to pull the wires in the wire harness to the switch. Remove the key sensor switch from the housing that holds the tumbler and switch mechanism. Remove the screw that holds the ignition switch body. Remove the electrical harness part from the back of the switch. Then, insert the key and turn slightly. Release the pin under the tumbler casing and pull out the cylinder.
Answer . There is no relay. The voltage comes from the fuse box directly to the headlight switch..
forgive my ignorance but i believe that the ignition switch is in the dash. first pull off the plastic coving around the switch and put the key in the ignition and roll it to …the ACC position and look for a button or sliding lock device that will release the the lock cylinder from the external casing. p.s. you may need to use a small screwdiver or an ice pick or a pen to push the button in. Unless you are ready to do some work the ignition on a import is a sealed unit and you will have to drill out 2 or 3 roll pins which are set at 11-2 and 6 approximatly, after removing these pins the cylinder(Thats were the key goes) will then slide out. Then you are able to insert a new cylinder. But if this does seem to be to much of a hastle then your local locksmith is able to do this for you.
Answer . \nInside the cab, behind the passenger side kick panel.
It is located on the receiver/drier. It threads into it and has two wires connecting to it. The drier is normally located near the battery just to the left of the radiator.
Answer . If you turn the ignition to the on position, and then press the interlock button, you don't have to press the clutch pedal down to start the truck.
Sometimes switches wear out, which could be the reason the switchin your 1992 Chevy truck is not working. There could also be aproblem with the wiring. You may also want to ch…eck the fuse forthe blower to see if it's bad.
On the top side of the steering column about halfway down, the high beam/low beam headlight switch should be bolted to the column right beside it. Inside the vehicle.
The 1992 Nissan truck air-conditioner pressure switch is located inthe fuse box. The fuse box can be found in the engine compartment.
\nThe battery seems good, there is plenty of power, nothing happens when you turn the key. Just started. Was able to jump across the terminals at the starter and it turned o…ver but would not start.
My 1992 Fire Bird has a 305 throttle body fuel injected.
The neutral safety switch is on the side of the transmission. Itscrews into the side and has a small three wire plug.
Remove the ring bezel from the front of the dash by gently pulling it. Then lift it over and to the left of the steering wheel and all that, would be holding it will be the l…ight switch it self, then just unplug it. Remove and relace the same way you did up till this point. J.d.
In GMC Sierra
Do you take the steering wheel off to get to the ignition
In Fuel Pumps
There is none. GM vehicles are not equipped with an inertia switch.
Dodge does not use inertia/reset switches. Dodge does not use inertia/reset switches.
you will need a couple special tools for this job. one is a steering wheel puller. remove the steering wheel. then you have to remove the turn signal stalk. then remove the tu…rn signal switch mechanism inside the steering column. then you need to compress the column locking plate to remove the wire ring around the steering shaft. after this its easy. pull the locking plate out and remove the screw holding the ignition switch in. replace switch and re-install in the reverse order. its easier to put together than get apart.