How do you replace the speakers on the door of a 2004 Chevy Silverado?
Take door panel off then it's as easy as 1-2-3
1 person found this useful
I just replaced mine this past weekend. For the passenger side door, there is a screw right under the door handle and a screw in the middle underneath the door. Remove them bo…th. Next remove the side mirror cover. It just snaps off. Now firmly but gently pull up and out on the door cover. It should come off. Now disconnect any wiring. For the driver side door there is an extra screw located behind the window and door lock controls. Just push in and lift up and out on the controls and the should pop out. Remove the screw. Disconnect the wiring before you continue. Next remove the same screws that you did for the passenger side door and the side mirror cover. Again firmly but gently pull up and out on the door cover and disconnect any remaining wiring. The rest is self explanitory. You may have to drill new holes for the aftermarket speakers to fit because the piece that held the factory speakers in was useless for mine. I also used some double sided tap with the foam in between the door and the speaker to help secure it and to provide some space between the metal door and the speaker. Hope this helped. I was pleasantly suprise on how relatively easy it was. You Can Re-Use Original Mounting and Wiring Harness: I just replaced the front speakers in my 99 Silverado and I Actually used the existing Speaker Brackets. I separated them from the old Speakers and then reattached them to my new speakers with a couple small 1/2" lg sheet metal screws and also pried off the existing wiring connector and was able to replace the speakers with Factory Wiring Harness and Mounting. 15-20 min's per side taking your time.
Answer . \nYou can usually figure it out by going to Http://www.crutchfield.com and seeing what fits your vehicle.
The Chevrolet Silverado speakers are replaced by first unscrewing two black hexhead screws, the first located in the door corner of the handle used for closing the door. The s…econd screw is located underneath the door lock, mirror adjuster, and window opener/closer buttons located together on a pad that is taken out by lifting up the outer edge and pulling it up and out. Disconnect the switches and take the screw out. Next, pull out the trim piece that surrounds the door handle and slide it off over the door handle. The entire door paner lifts upward and outwards, but use care to keep the panel close to the door until the courtesy light, door lock, window, and mirror buttons are disconnected from their switches. These connections are the typical automotive electrical switch push lock types that slide out once unlocked by pushing them down. At this point, the entire door panel comes off revealing the 6 1/2 " speaker. The speaker is easily taken out by pressing down and pulling outward on the top of the barcket that holds the speaker in place. The speaker can then be disconnected from its electrical connection. The plastic bracket that holds the speaker in is glued to the speaker, and unless a factory speaker is used to replace the unit, one may have to pull the bracket off of the old speaker, and glue it to the new speaker. Factory OEM speakers will come with the bracket already attached, and with a foam protector on front of the speaker. The part number is 15038566. Reassemble by connecting the speaker switch and replacing the speaker and bracket. Hold the door panel up to the door, connect the courtesy light and replace the door panel by sliding its lower plastic slide guides into their slots, then hold the panel close to the door and slide the panel down until it snaps into place. Replace the two black hexhead screws. Make sure the door lock, window and mirror electrical connectors are easily within reach and connect them to the pad of buttons. Slide the pad in and down until it snaps into place. Replace the trim around the door handle.
You remove four screws with a small L key and then carefully remove the top plastic from the speaker ......then remove the speaker from the lower plastic.....Its a bit tuff bu…t it can be done and then replace speaker.....you also need to remove the receiving part from old speaker and use it to connect you new one. or you can cut off the plug and connect speaker direct and tape it
you have to take the entire door skin off,arm rest,switches,etc.remember how you took everything apart so as put everything back again the handle has basically to bolts holdin…g it in place one outer side of door edge,above the Vin number,sticker on the door,the other you will see when you take apart the door it will be exposed,you'll have to physically look inside the door at the handle itself,take it out and the handle practically off,using medium sized flat head screw driver,pry the pin that connects the from the door(i forget what this things is called,the part that latches or actually grabs onto the door striker)to the handle base,theres another one you may or may not be able to see at first but as you start to remove the handle from the door it will become looser and you should see it from under the handel outer door,pry it loose and your home free.realize this isn't going to be easy it at all and if you can have someone assist you that knows what there doing,use them,you'll be happier for it.
Open your door. Look at the edge of the door. There is a bolt just about even with the handle. Take that out and then remove the inside door panel. There should be a whole at …on the inside even with the door handle, take that out and the handle should be lose. You will then have to take apart the clips that work the lock and door latch. Its not simple, but if you are half way mechanically incline you should be able to do it.
remove the screw under the door handle on the inside, and the screw under the panel(front only) and gently lift straight up and there you go! the only thing really holding the… panel on is little arms that slide down into a hole all over the backside of the panel. so putting the panel back on isn't a job either.
How do you replace the speakers on the doors of a 2002 Chevy 1500 Silverado pickup as well as the speakers in the panels on both sides of the rear window?
For the front speakers your gonna have to take the door panels off to get to all the wiring and everything and for the back ones you should just be able to take the plastic co…ver off and replace them
Front Door Speakers are 6-1/2"
6x5 IN THE FRONT DOORS AND 4x6 IN THE REAR
if you are talking about the extended cab, you have to take the 2 panels out and be careful doing so or you can break them.
Remove door panels.. Unscrew old speakers..Screw in new speakers..replace door panels...ready 2 GO..
pop the cover take 4 screws out & put your new 1 in
In Chevy Tahoe
6 3/4 oversize 6.5 in the front door
The door speakers are 6 1/2 " round...still looking for the size of the rear ones.
4 x 6
remove the door panel