How do you replace light switch on a 1990 ford ranger pickup?
1/ remove the headlight switch knob by pulling out the knob rotate until you find a slot , use a small blade screwdriver pry the knob off .2 remove the trim on either side of the steering colum ( on my truck this is kind off a chrome colour ) under this trim insert there is one screw per side 3 using a blade screwdriver remove the plastice around the insterment cluster , start at the top working to the side 4 unplug the tank selection switch ( if equiped ) 5 on the automatic yu will have to put the trans in 1st gear to remove the dash cover6 remove the 2 screws holding the headlight switch
2 people found this useful
Answer . It depends on what part of the country you live in. Call a couple of local garages for estimates..
ignition switch replacement I found that by removing the steering column shroud you can access the small hole in the bottom of the key cylinder.When you put the key in and tu…rn it to the "on" position push a small awl or similar tool into this hole which pushes the catch pin and you should be able to pull the cylinder assy out.With the new cylinder in the same key position just push it back in and reassemble column.
Answer . \ngo to autozone.com and look in the online repair manual they have
New Answer Using your current key, insert it into the ignition & turn the ignition to the "On" position but not the "Start" position. Do not start the truck. Next, using a ve…ry small screwdriver (preferably a Phillips head) insert it into the hole located under the ignition key cylinder on the steering column. Pressing upwards with the small screwdriver or nail, you will press in the release button. Firmly grip the key & ignition cylinder while pressing up on this release button & remove while in the "On" position. Insert your new ignition cylinder with the key in it, into the "On" position until it snaps in place. Going in, the release button does not need to be depressed. You now have a Cylinder key, that will not match your door lock keys! Best of luck.
Answer . \nford doesnt have a ram pickup\nram is dodge
Answer . \nFirst of all disconnect the battery remove steering wheel , there is a round slot in the steering column you insert a rod in there it will release the switch ( …be sure to remove negative cable or air bag can go off. You may have to twist the switch back and forth to remove
i have a 1994 ford f150, which is real similar. i recernly changed mine out. under your steering column is a small hole. use a Philips or something with a flat end and put in …there. do not jab but push up and if u look in before u will see a spot. push the device in the hold at the spot and once u have the spot lined up and begin to push, have ur old key in the igtion. the piece u stick the key in will come out very easy if pushed proprly. aftr that the new one will lock right into pleace.
i need a top cap button for the on-off switch for the cruse control
1990 ford ranger brake lights wont work we checked fuses bulbs and changed brake switch any other ideas?
Answer . \ncheck that you have double filament bulbs in tail lights
Answer . in the fuel tank
Sounds as if it is out of alignment, like someone is still steping on the brakes as you leave the vehicle. Or if some rewiring was redone, recheck it. Or your light switch is …not working properly.
very simple remove 2 screws holding housing around lever, then u can access switch without any problem i think only remove 2 taps. i worked on my 99 ranger this should be same…. . bobby . russell springs, ky
Theirs to 2 bolts directly behind it (on the corner wall of the bed haul). Unscrew and wow the lights in your hand.
take the steering wheel off and take the ignition lead off and then you buy a new ignition with new key or vis versa
In Chevy S-10
First you have to drink a beer and access the situation. Next step is to remove the fat chic from behind the steering wheel. Then remove the steering wheel and hand it to the …fat chic. Next drink a beer. Now you're ready to remove the steering column, drink another beer. Pull the thing apart, drink another beer. This is actually a big pain in the butt. Drink another beer, access it a little more. The neighbors are coming over to drink, we'll finish tomorrow.
you have to take the bed off and it is near the cab on the driver side but i cut a hole in the floor of mine and welded it back on good as new ha-ha
I'm not a mechanic / technician but check in the front passenger foot well , under the front edge of the carpet , mounted on the toe board just to the right of the transmiss…ion hump ( I believe that is where the fuel pump inertia switch was on my 1993 Ford Explorer )