How do you install projectors headlights on a 2002 mustang?
Stick them in
1 person found this useful
how to change headlights on a 02 mustang I just did this today...(2002 mustang gt) when you open the hood on the back of the headlight assembly, there's a long metal clip. Th…is holds the entire assembly in place, take this out using the tabs (gently). the whole assembly should slide right out, then unscrew the large plastic nut that holds the bulb in place. to remove the bulb just twist. it's pretty easy to do and takes zero tools (yay). the foglight bulbs are a different story. still trying to figure that out. . erik
ReplacingHeadlightBulbs.pdf . \nhttp://home.comcast.net/~slashpub/headlights/ReplacingHeadlightBulbs.pdf
A step by step tutorial can be found at AudiWorld in the Tech Articles section. Visit www.audiworld.com and the Tech Articles are found in the menu under Resources. Select E…xterior and look for the article titled, " BOSCH Euro Headlight Installation (for pre '99.5)" by Todd Becker. There are other articles however, his is the best starting place. I apologize for sending you on hunt for the site but direct links to those articles are difficult and a proper answer does not fit within the scope of Wiki Answers.
Answer . open the hood and access the headlight housing from engine compartment. Twist round plastic ring lock, unplug terminal, reverse your steps. Good Luck........
splice together both stripped wires for headlights and run your projector lights to your fog lights or park lights
First you should make sure that the lights you purchased already have the harness that connects to the wiring that your stock lights were connected to(mine did so that's what …i know how to work with). Second, if your lights are anything like mine, you should have 3 sets of wires on the bottom of the lamp housing( 3 sets of red and black wires). These wires go to the halogen halos around the actual lights of the headlight. I found it best to wire these wires to a toggle switch in the car that way your halos are not on all the time(which could cause them to burn out, they are mainly for show and to be all fancy and what not) and you can control when they are on. Third, your lamps should fit directly into place of your old lamps. There also should be wires to hook up the blinker light that is in your new setup. I have not take the time to wire these up yet. The bulb on the outside of the lamp is your regular light and the bulb in te middle is your brights. Nothing extra for this, just plug and go. Your neighborhood friendly focus freak.
Pull out the light by pulling out the two metal rods holding your headlight in place. Take the headlight out by slightly turning the plastic rings around the back of your ligh…t. It should loosen up. When it does, just mess with it a little to pull it out, pull out the bulb and replace! =)
Halo projector headlights are direct bolt-ons to a 2005 SRT 4. Toinstall a unit mount the light to the bracket in the front bumper.Connect the light plug to the wire harness a…nd splice in the sidemarkers.
Nope, but it makes the job a lot easier! :)
If you already got the halo assembly if not you need to go and get new halo headlights eBay i got mine for celica free shipping, then when you get them just connect up all the… wires and then there will be one extra wire that you will have to ground to make halos work. All done nice cool looking headlights good job :)
Most replacement headlights come with plug and play assembly! So all u will need is a socket set, and remove three screws from each headlight! Once screws are off, u disconnec…t the plug, and remove ur old headlight assembly!Grab ur new halo headlights, set them in place, plug them in, put the screws back on and ur done!
Your projector headlights should come "plug n play" and have the female ends for your existing connects on the wiring harness. As for the additional wires for the halos the b…est or easiest way I found was wiring them into the parking light circuit. This worked for my projectors on my truck.
In Grand Am GT
(@)(@) V (@)(@)________________..................................................................................... ________________. Here is the Diagram
The 02 F150 did not come stock with projection headlamps. The lamps are aftermarket if they are the projector style. If they are of decent quality, there should be a couple of… "gear" like looking wheels on the back of the assembly. by turning these two wheels you will lower/raise the beam and also move it horizontally left and right. If not, you are sol.
How do you install projector headlights on a 1998 Chevrolet corvette
In Grand Am GT
This is how I did it.. I connected the black and white halo wires the the extra bulb housing with the brown and black wires. Then, my high beam lights were wired to my fog lig…hts because the standard big plug doesn't work with the high beams and low beams. Again, that is how I wired it. Don't forget, you basically have to cut out most of the plastic housing so the head light will even fit.
Projector headlights provide a much more intense beam of light for your car. According to CarPart4U, "Stylized projector headlights allow for a much more concentrated and i…ntense beams of light for your car driving lights needs. Projector headlights direct light beam penetrates the air, allowing the projector headlight to illuminate farther down the road than run-of-the-mill parabolic headlights." http://www.carpart4u.com/autopart/Projector-Headlights-p-1-c-6.html