How do you change spark plug Mercedes C220?
Remove the engine covers and carefully remove the ignition wires from the spark plugs, there are 12 of them, then remove the spark plugs with a 5/8 plug socket. Make sure the gap is correct on new plugs put a bit of anti seize on the threads then install the new plugs...
3 people found this useful
Answer . Please use this for reference only since I have a 1996 C 220.. On the top center of the motor is a cover over the spark plugs. Remove the cover and you should se…e your plug wires. Obviously just unplug wires and remove the plugs. However I did not have a spark plug wrench the held the plug so I had to put the plug into the wire and slightly twist the plug into the opening. I then removed the wire again and used the wrench to tighten. Only do one plug at a time obviously.
Pull the HT leads off (one at a time so you dont get them mix up). Using a deep socket, (socket sets usually have spark plug sockets included) undo the spark plugs like you w…ould a nut..... Lefty - loosey. Righty - tighty. Pull the HT leads off (one at a time so you dont get them mix up). Using a deep socket, (socket sets usually have spark plug sockets included) undo the spark plugs like you would a nut..... Lefty - loosey. Righty - tighty
I have no idea how to change spark plugs in any vehicle, let alone my 2003 Mercedes-Benz C230 (sports coupe). I did find a helpful series of videos on Expert Village (www.expe…rtvillage.com) and you can access the series at this link: http://www.expertvillage.com/video-series/452_spark-plugs-automotive.htm. Good luck. I am going to try to change mine tomorrow just as a preventative maintenance.. ans Fairly basic...the plugs are found after removing the 3 screws on the shield on top of motor that hold down the little inspection panel. The plugs themselves are in the deep holes.
Answer . headlight bulb?..........push big tab on the black bulb cover and take it off........you see wires and connector....... wiggle and pull connector (not the wires) …off the bulb terminals...... a metal wire retainer keeps the bulb in place......to release the retainer push inward and left.....remove spent bulb....new bulb (do not touch glass) fits one way only...........replace retainer........replace cover. entire episode takes about 5 minutes OK!
Disconnect the battery, remove the air hose to the throttle body,remove the access plate, remove the spark plug cables and theboots, and remove the spark plugs. Replace the sp…ark plugs, replacethe boots and cables, replace the access plate, attach the air hoseto the throttle body and connect the battery.
First off I have to assume the that the engine arrangement is the same for the 2001 as a 1999 model. 1. Remove the air inlet cover that runs over the top of the engine by uncl…ipping at the air filter end and loosening the massive jubilee clip at the other end and sliding it off the rubber retainer. 2. Using a suitable sized Allen key remove the cover on top of the engine block. You should now see the HT leads leading to the sparkplugs. 3. Two of the sparkplugs are accessed by pulling up the plug cover two have covers held by male torx bolts. You will need to uy a special female torx bit for this. Unscrew these and pull up to access spark plugs. 4. Loosen the sparkplugs with a suitable deep socket. I found it easiest to loosen the plugs and extract by pushing the covers over them. The rubber grips the plug and it can be pulled out from the deep recess. 5. replace with new plugs and working in reverse, fit all the bits back that you have removed. I hope you find this useful.
Disconnect the car battery, remove the spark plug cables and bootcovers, remove and dispose of the old spark plugs. Next, put in thenew spark plugs, attach the boot covers and… spark plug cables andreconnect the battery.
This is a plug and play installation. The door trim will have to beremoved for the door(s) that have bad lock actuators. Once removedthe motor assemblies and control solenoids… can be accessed. Thesolenoids will have a black wiring harness attached. This can bequickly disconnected and the new actuators replaced. If connectorsare dirty or contaminated they can be sprayed with electrical partscleaner first.Ã
It really is not too difficult. I assume you have a six cylinder engine like mine. The slight difficulty I had was removing the spark plug wires. The plugs are deep in there s…o the wires have a long metal end. When I removed the first one it broke off at the meeting of the rubber and the metal. I had to buy a new set- not cheap. $75 at Auto Zone. Beyond that, the job is easy. Access is very easy. It has an aluminum head so you must use an anti-seize lubricant on the new plugs before you put them in.
actually it is a ml320
\nI would take a few of the plugs out of the engine and check them for wear. You might not need to replace the plugs because of the efficiency of the electrical system. You …might just need to clean your plugs and re-gap them.\n. \nIf you do need new plugs:\n. \ngo out and buy 16 brand new plugs for the car,, there are 2 plugs per cylinder. The parts store will have the info for the right size. Plugs in these cars should last a minimum of 25,000 miles.\nGet a proper plug socket and make sure your socket slides all the way down so you don't break the ceramic insulators. \n. \nI like to rub a very very small amount of an anti-seize grease on the bottom of the plug's threads...it helps when you need to remove the plugs later. Always hand screw the plugs in as far as you can before using the socket on them. Again, spark plugs are fragile and break easily.\n. \nIf you're asking this question, I assume you're a newbie at this. Remove a plug wire at a time so not to cross wires...which is hard to do, but not impossible. And don't man handle the plug wires...they're silicone and can break easily, which will make your car idle like a tractor. And lastly, make sure the car is cold, otherwise you'll sear your hands.
http://wiki.answers.com/Q/How do you change ignition switch in Mercedes C220 "
On the top of your engine is what looks like a cover (coil cover) with 6 10mm bolt heads. Across the back is your air intake coming from your air filter. Remove this and tempe…rature sender, located on drivers side, where air intake is attached to engine, and it will expose the coil cover of your engine compartment. Remove the 6 bolts. Remove this cover, exposing your spark plugs and coils. There is one coil for 2/ea spark plugs. Going on line, you should be able to shop around and buy the coils and plug wires for at least 50% less than at automotive stores or MB. Be careful on removal and installation that you don't break the plugs. I suggest if this is your first time, have the new plugs, wires and coils at hand before starting and as you remove a set, replace them immediately so you won't forget how you took them out. A cool car would be suggested starting this procedure, as it will be very hot in that location. Installation is reverse of removal of course. I hope this was helpful.
easy.........take the old spark plugs out and put the new spark plugs back
You need to disconnect the air filter which runs over the top of the engine, disconnect it a both ends, the one with the clips and the one with the jubilee clip, remove ends o…f contact and slide the pipe to the left carefully so it's not attached to the engine. Take an Allen key and remove the three large bolts on the top of the engine, these have the holder on them for the air filter. Under the plate you should have 2 large coil packs and 2 HT leads. Remove the nuts holding the coil packs down and underneath you will have spark plugs, carefully unscrew them using a long socket with a rubber bung in it so you don't drop the plug once its been loosened. Hope this helps. Just done this today!
how do i locate the coil pack on a 1998 Mercedes c200
Changing the spark plugs in a Mercedes w208 320 1999 only requires two tools to be used. The first tool is a 3/8 wratchet that has a short extension and the second tool part i…s a universal socket. Attach the universal socket to the spark plug socket and use the wratchet to loosen each spark plug. Use the same tools to tighten the new spark plugs into place.