How do you change a tail light for Jeep Liberty?

already exists.

Would you like to merge this question into it?

already exists as an alternate of this question.

Would you like to make it the primary and merge this question into it?

exists and is an alternate of .

1) You will need to open the rear swing door. 2) On the inside jam there are two torx headed screws (T-15's if I remember correctly). 3) Unscrew the two torx screws. 4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet). 5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick). 6) The lilght bulbs are twist mount settings inside the light casing. 7) Twist out the mount setting, change the bulbs, and reset the light mountings. 9) To put the light casing push the light casing back on and put in the screws.
31 people found this useful

How do you replace a tail light in a Jeep Liberty?

Open tailgate and use a #20 Torx screwdriver to remove two screws located on the inner side tail light assembly. On the driver's side, the screws are accessable through the ta

How do you remove a Jeep Liberty tail light to replace a bulb?

Simply use a Torx wrench. I can't remember if it's a size 15 or 20, but it's pretty easy. Look closely for the Torx screws. I believe you have to open the tailgate to see them

How do you replace a Jeep Liberty tail light?

Trying to replace passenger side tailight on a 2002 Jeep Liberty. Cannot disconnect the plug and the replacement connector looks different from the original! Thanks Jim

How do you replace a tail light bulb on a Jeep Liberty?

Open up your tailgate and on the sides of the taillights will be screws, you need a Allen wrench or Allen type screwdriver. Unscrew them and pull out the taillight assembly (u

How do you change the left tail light of a 2002 Jeep Liberty and how do you access the screws?

Answer . 1) Open the swing door and look into the hinge area. There should be two torx head screws. These are size T15. 2) Remove the screws and then remove the lens. The l

How do you Change side marker light 2005 Jeep Liberty?

1. Turn the front wheels full lock toward the same side of the vehicle as the lamp being serviced. 2. Disconnect and isolate the battery negative cable. 3. Remove the four fas

How do you change tail light bulb on a 2004 jeep liberty?

replacing brakelight for 04 Jeep Liberty . By opening the tailgate, you will see two star headed screws. you may need an extension and good lights to get to them. Carefully

How do you change tail light on 2003 Jeep Liberty?

To access the driver's side tail light, open the tailgate. There are two torque head screws that hold the bulb housing in place. These screws can be removed by reaching a regu

How do you change brake light 2004 Jeep Liberty?

Answer . I own a 202 Liberty. I changed the rear brake light/ tail light myself. To change the passenger side is easy. Open the rear door and locate the two screws that hol

Why do you keep blowing tail lights 2002 jeep liberty?

Check for usage of incorrect bulb. Check for incorrect (excessive) or fluctuating battery voltage with engine speed of 2500 RPM and while revving the engine (snap throttle.)

How do you change a brake light on a jeep liberty 2003?

This is an easy one. Remove the two screws that hold the taillight to the body. They are located just inside the tailgate. The taillight has two tabs the fit into slots opposi

How do you Change dome light 2002 Jeep liberty?

The two map reading lights next to the trip computer are bulb type 194. There is a hole for a small phillips head screw at the front end of the plastic bezel, very near the ed

How do you change the drivers side tail light bulb on a 2006 jeep liberty?

2006 Jeep Liberty tail light bulb lamp replacement: Purchase the correct replacement tail light bulb(s) first, before disassembling the vehicle. See sources and related links

How do you change brake light bulb on jeep liberty 2006?

2006 Jeep Liberty brake light bulb lamp replacement procedure: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and re