2000 Chevy blazer What if your turn signal flasher behind the glove box keeps flashing and only goes off when you apply the brake pedal all signals and lights work how do you fix this?
First turn on the motor with the garage door closed then heal the compressor
1 person found this useful
How do you fix the problem of the brake lights and turn signals and emergency flashers not working when all fuses and bulbs are good?
%REPLIES% The WD40 solution I had the same problem on my 98 Grand Marquis. A Linclon Mercury mechanic told me the problem was most likely in the hazard flasher switch on top… of the steering column. He recommended I spray WD 40 around the switch and push it down *and let it pop up several times and wiggle it around. It worked for me - problem solved. Apparently, over the years gunk finds it way in there, be it dirt, liquids, etc. Furthermore, he said there is no "flasher" you can replace as you may remember in older vehicles. Good luck. The rest or these posts are simply testimonials for the first answer . The WD-40 squirted in the emergency flasher switch worked in my 97 ford mustang. Thanks so much for the info. . Thanks for saving me the coins to pay a mechanic. I have a 97 Ford Van and the question fit my problem to the tee. The solution also fixed my problem. . My wife push the flasher and that started all the problems. I took your advise and it worked for me too on my 1995 Grand Marquis. Thanks for your imput. . I have a '99 Ford F-150 4.8 Liter V8, and this seems to have fixed the problem. It began as an intermittant problem and has gotten progressively worse over the past couple of months. I thought it was only affecting my turn signals, but I later discovered it also involved my brake lights. Moving the emergency flasher switch up and down a number of times solved the problem. Thank you! . This also worked for me I have a 1999 Ford Expedition. I moved the hazardous lights up and down and the problem was solved. . I thought I had checked the relevant fuses on my Ranger truck, but missed the one for brake-Emergency Flashers. My flashers were on - the button in the extended position when the fuse blew. Because the fuse went I didn't know the flasher was still in the on position. Therefore the turn signals and brake lights didn't work. It wasn't until I got the flasher in the off position that the turn signals started working again. . hey it worked for me too! i almost brought her in to the vultures till i found this. thanks!!!! . Worked on 1998 Lincon Continental...moved hazard warning switch in steering column up and down....worked great! THANKS! . The WD40 worked like a charm. I have been trying to fix this problem for 2 hours. I sprayed WD40 and problem solved. Thanks so much. . It works , don'ask me how , but it works. . Just used WD4O on the hazard switch of a 97 Aerostar whose blinkers have not worked for months. The switch now works freely, and the blinkers work, too. . I had a right front turn signal not working, sometimes. Then the left front stopped working, sometimes. Replaced lamps and still no joy. Tried the hazard flasher switch a few times and it started working but only sometimes. Sprayed WD40 into the hazard switch, exercised it a few times, and all OK now. Many thanks to the original poster. . Good Morning! Let me echo the repair of the WD40. I had the same symtems of turn signals, flashers not working. Checked all the fuses. Went to Auto Zone to seek advise, They called FORD for me (really nice guys here in Warren, Pa) Ford pointed them/me to a light processcor that costs in excess of $200. A dealer only part) Auto Zone then suggested for me to access the web and seek out like problems which I did. Thank you to the original poster of this issue and Auto Zone. Several squirts and I worked the switch...and presto...everything started working again! No cost at all to fix this prob. I already has the WD40! . It worked for me too on a 1997 Ford Thunderbird! Took me 2 days of checking things and not being able to use the care before I "Google'd" the problem. The Internet is great and so is your web site! You should have an option for people to pay something if you site helped them. This was worth at least $50 (and more if I would have taken it somewhere). . Thank you VERY MUCH !!! The WD-40 solution worked GREAT !!!!!!!!!!! . Thank you, worked for my 1997 F-150!
Why does the turn signal fuse on a 1996 Chevy S-10 blazer keep blowing but the emergency flashers work fine?
Because the turn signals are a completely separate curcuit from the emergency 4 way lights. The turn signal wiring has a short that causes the fuse to blow out. In order to fi…nd that short, you need a technician that specialises in electrical wiring repairs, because you could spend days trying to find it and fail. It will cost some money but less than the value of the truck, or a traffic ticket for "no signals."
You have 1998 Chevy s10 blazerLS The turn signals and hazard flashers do not work Fuses checked They are good Replaced 1 combination hazard flasher located behind glove box but still no change?
Answer . \nReplace the turn signal flasher first under the dash near the column but You may have a bad turn signal switch. On your model, the hazards and turn signals use t…he turn signal switch assembly. New $300+ ;salvage yard $ 40.00.
Answer . \nMy first guess would be to check the fuse box under the hood on the drivers side. There is a diagran under the lid which shows what fuse to look for. Answer … . \nMy first guess would be to check the fuse box under the hood on the drivers side. There is a diagran under the lid which shows what fuse to look for
Have a 1998 Chevy Blazer What would cause the turn signal flasher relay to make clicking sound all the time even though turn signal not on The only time it quits is when the brakes are applied?
Answer It's the stick thingy and wiring in the steering wheel. The thing you use to turn them on and off has a short. Replace it and it's good as gold. see "link" below Sorr…y, but the stick thingy is the wrong answer. I have a 1998 GM Blazer and the exact same thing happened to me. It sounded exactly like my directional signal was on, but it was not. It actually started to drive me crazy because no one could figure it out. When I put my foot on the brake, the clicking sound would also go away. Mechanics thought I was crazy. Two years later, I found an independent mechanic and he did 2 things to correct the problem. (1) Replaced the 4 wheel drive switch on the dashboard, and (2) Replaced the solenoid switch under the dash. The clicking sound was gone for good. Good luck, hope you get it resolved.
Brake lights don't work with headlights on only right side brake lights partially with headlights off Right turn signal in rear works always left turn signal flashes quickly always Any advice?
You have some problems with electrical connections. Most likely the ground wire of the tail lights. Also, the left light may be burned out or have a POSITIVE wire connection p…roblem.
My 2000 firebird's left turn signal has stopped working the turning lights are out on that side and the flasher on the dash doesn't flash at all what do you think the problem is?
Answer . \nIf you put the left turn signal on and it flashes quicker than it does if you put the right turn signal on I'm pretty sure one of the bulbs is out. Park your c…ar with it running and the left turn signal on and walk around the car and see what isn't flashing that should be. Then you know what bulb to change, it should give you the exact bulb type/number/color in your owner's manual.
What would cause the left turn signal to flash fast when the brakes are applied at regular speed and when the brakes are disengaged on a 2000 Chevy Venture?
\n. \n Turn Signal Problem \n. \nUsually the fuse is going bad.
What causes both turn signal lights to flash when either signal is turned on and to stop when brake is applied only when lights are on?
Answer . It depends on the car. Some cars require that you turn on the turn signals to make the 4-way flasher work. If that's the case with your vehicle, make sure the eme…rgency flashers aren't on.\n. \nOtherwise, it's probably a problem with the turn signal switch.
Check bulbs they are double filamented (smaller for brake/turn larger for tailights Check the sockets for corrosion Check ground . have you checked your fuses?
What is wrong with your 2000 Pontiac Montana when you press the brake pedal and put on your turn signal the lights all alternately flash?
There is a ground fault in one of your wire connections into yourtaillight. It is usually a connector for your rear light assembly.Remove the plugs from the tail light assembl…y starting with theside that blinkers flash fast when brakes are applied. You willfind that the pin to your ground will have a blackish tint to thepin (on the brake light assembly). Clean this pin and thecorresponding plug recepticle. I added a tiny piece of tin foil tothe plug in the ground pin hole to ensure a tight connection. Plugin the unit while not installed and see if that eliminates theblinker lights from coming on on the dash when the brakes areapplied and the blinker is on.
Your turn signal flasher behind the glove box keeps flashing and only goes off when you apply the brake pedal all signals and lights work how do you fix this?
It's easy, just go to a gasoline station and ask them to check theblinker.
What fuse controls the brake lights on a 96 Chevy 1500 All lights and turn signals work except no brake lights when brake pedal is pushed?
I'm not exactly sure which fuse it is, but it doesn't sound like a fuse to me. I would check the switch on the pedal, just simply short acrost it from terminal to terminal wit…h a screwdriver, if the brake lights come on, the switch on the pedal is bad, if they don't then it probably is a fuse.
The turn signal flasher on a 2000 Chevy Blazer is located under thedash. It is just above the gas pedal and slightly to the right.
In Chevy Blazer
\nprobably have a bad relay, that was my problem.. Are your turn signals not working, but your hazards lights are? and if so, do you hear a constant clicking sound, like your …turn signal is turned on? Does the clicking sound go away when you hit the brakes? It is the relay.
Why do all the signal lights flash plus the middle brake light when you give a turn signal on a 2002 Chevy Silverado.?
You may have a bulb that that brunt a element which than crossed the other element cause all lights to come on a one time. I have seen this before. If this does not light all …bulbs when the brakes are applied, then I would be looking in the front lights, if it does I would look in the back lights.
Some vehicles have a master electical control switch mounted on the steering column that controls all those functions