06 murano axle nut size?
I believe its 24mm
2 people found this useful
The rear axle nut size is 1 3/8" according to my Haynes manual. The front axle nut can be removed with a pair of channel lock pliars as shown in the Haynes manual.
if 2000 and above, it should fit between 34mm to 36mm depending on axle, most are 36mm 35mm
Answer . It is 36mm. A 1-7/16 inch will also work. The sockets for this are readily available at auto parts stores. Have you got a good strong breaker bar, because those babies are on there TIGHT!
Answer . EITHER 30MILLIMETER 32 OR 36 MILLIMETER. I 'vote' for the 30mm - Ford seems to use that size often (Sable/Taurus have 'em too)
The rear wheel hub spindle nut (axle) size is 30mm. I just changed my rear wheel hubs today
Answer . If you go to Autozone they rent the socket. I believe it is a 4 or 5 prong socket. Not a conventional socket. Just tell them what year, what tonage (ie 1/2 ton, 3/4 ton etc), and that it's 4 wheel drive. Good luck.. Lonjames1 at hotmail dot com
The Chevy S10 were small pickup trucks which were made from1982-2003. The axle nut size for an S10 is 36mm.
once you remove the retaining tabs off of the washer that are covering the nuts, it takes a 34MM DEEP SOCKET
According to the GM service manual on a 2000 Cavalier it is 144 lb ft. I would assume this figure is true for 1995-2005 models since major parts like this did not change.
Many Dodge trucks have an axle nut size of 44. However, one shouldcheck the owner's manual or a repair manual to be sure.
The size of the axle nut for a Volkswagen Polo has changedthroughout the years. Older models used a 30mm nut while newermodels use a 36 mm nut.
You will be able to find this by the tires of your vehicle. You mayneed to get a replacement part if something goes wrong with thevehicle.
http://wiki.answers.com/Q/What size socket do you need for the axle nut on a 2003 mitsubishi galant "
\n. \nThis is a special nut because it's deformed to retain torque. It's also a one-time use nut. You can get a replacement at any dealer or auto parts store. But do NOT replace with an ordinary nut. I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technol…ogy. (MORE)
The axle nut torque specifications for a 1998 Chevy 4x4 are 165 lbft. The metric specs are 225 N m.
I have a 1997 dodge ram 1500 4x4 with a Dana 44 front axle i need to change the axle u-joints but i cant find out the size of the catle hub nut nor the 12 point knuckle to hub bolts. HELP?
I have just had my axles out of my 2000 ram 1500 and the sisze of the axle nut is 1-11/16 and the hub to knuckle bolts are 14 mm 12 point hope this helps. Go to rockauto.com they have what you need. you do not need to remove the nut. take off the brake calb. there are three bolts behind where …the calb is bolted on . remove the bolts and the shaft should pull out. i will try and look up the web site for step by step directions any problems write me at email@example.com (MORE)
The axle nut for the 1982 Dodge Rampage is the size ofÃ2-9/16. Youneed to know the exact size in order to get a socket to remove thenut.Ã
The axle nut on a 2000 Tiburon is 32 mm. These nuts are incrediblyhard to remove and is usually easier to use an impact gun to loosenit.
Answer: . The front axle nut on a 1994 Plymouth Acclaim is 32mm OD. A 32mm axle nut socket should be available at most parts stores.
You don't need to take the center axel nut off to remove the rotors. Take the calipers off (two 13mm bolts on the back side) and the rotor will pull right off. If it's rusted to the hub you might have to bump it with a block of wood, but they usually just slide off. You only need to take that big ce…nter nut off if you're pulling the axel. (MORE)
The axle retainer nut is likely to be the same as on the 1998: 30mm
this should be easy to find but it isn't don't know why ! people that right on forums are to stupid to include ........ " remove the axle nut" correction = remove the axle nut using a 29mm socket! how hard was that !!!!!!! 29mm is what you need for that nut !
Answer: . The inner thread dimensions are 24mm / 1.5 pitch, so the outer dimension of the nut is most likely 36mm.
The axle nut torque for an Acura Legend is 206/285 ft-lbs/Num. Foran Audi 100 Quattro, it is 147/200 ft-lbs/Num. For a BMW 5 SeriesRWD, it is 221/300 ft-lbs/Num; and for a Buick Enclave, it is151/205 ft-lbs/Num.
My Toyota Sienna 2000 axle nut measures 30 mm Sprayed the threads as I will be replacing an axle shortly. Probably the same size.
Axle Nut .. 1994 Nissan Altima ... 36mm socket. You will need a 1/2" Impact or breaker bar. Most parts stores have a loaner program where you can borrower this socket.
I have read that answer on our forum the other day!\n. \nIt is an odd size. Come to our enthusiasts forum for all your answers!\n. \nwww.trailvoy.com
The axle nut on the 07/08 Yamaha grizzly and rhino is a 27mm. It has standard threads but you need to use a breaker bar with about a 3 1/2 foot cheater pipe.
30 mm. You need a normal chrome 12 pt socket instead of 6 pt impact.
The axle retainer nut is a 30mm Torque spec: 170-203 ft. lbs. See "Related Questions" below According to the Autozone.com repair guide (see "Related Links" below), the torque specification for the axel retainer nut is 157-212 ft. lbs. EITHER 30MILLIMETER 32 OR 36 MILLIMETER I 'vote' for… the 30mm - Ford seems to use that size often (Sable/Taurus have 'em too) The axle nut should be 30mm See "Related Questions" below for more Axle nut torque specs are 170-203 ft.lbs (MORE)
What size is the axle - hub retainer nut and its torque specification on a Ford Taurus - Mercury Sable?
I can say from very recent experience: 30mm Torque: 170-200 ft. lbs. Torque specification for axle nut: 170-200 ft. lb. The axle nut should be a 30mm. See "Related Questions" below for more Driveaxles : 2003 Ford Escape 3.0 v6 XLT driveaxle/hub nut ..........................214 Ft-l…b 290 Nm ' '290 Nm (MORE)
The front axle nut on the 4+4 should be 35mm. You can use a 1 3/8" deep socket but it will fit tight. On my 2000 Chevy s-10 the Nut was 36MM. The socket I bought at advanced auto says right on the package for GM axle nuts.
well its all about ur brain so use it but dont go and eat vegeables caue it may not work good luck u tuna fish cakes:)
use an impact gun and the proper size impact socket. and make sure its turning counter-clock wise to remove.
I just did mine. It required a 33mm socket. Put a screwdriver through the hole in the caliper and into the cooling veins in the brake disk to prevent it from turning while loosening/tightening the axle nut.
1. Buy the correct-fit replacements. The 2006 Nissan Murano takes a special 14" rear wiper blade for the special rear arm. Your dealer will have them (may be expensive) or you may want to look into "Trico Exact Fit Rear Integral Blades" that fit these new special arms - you can find them online. (th…ere may be others available too) The good news is - specialized rear arms do not automatically mean the wiper blade is difficult to change - it just means you need to get the right blade for easy (and successful) installation. Correct replacement windshield wiper blades are not only correct length, but also correct attachment. Never just buy by length only. Always lookup your vehicle in an application guide at the store or now-a-days you can 'lookup wiper size' online. The key to an easy install is correct size/correct part numbers. 2. The new replacement wiper will have step-by-step, illustrated instructions for removal and installation. Take your new wiper blade and instructions out to your vehicle and physically get the old and new wipers in your hands and take a look. The instructions will make 100% sense once you're looking and touching them. 3. Most wiper replacements snap off and on, do not require tools and take approximately 2-15 minutes. (MORE)
200 ft lbs then adjust the nut to the closest hole for the new cotter pin make sure u spin the tires while torquing the nut
if you have the old style nut (keeper pack with multiple nuts inside) torque it to 284 ft.lbs. - If you have the newer style solid nut, torque it to 173 ft.lbs. if you do have the old style nut i recommend that you replace it with a solid nut due to the fact that the older ones have been know to cau…se some bearing failures. (MORE)
You can change the axle length by installing a longer axle. You cannot change the axle diameter because you are limited to the diameter of the bearing cups, races, etc. allowed by whatever particular hub is being used.
IIRC It is a 38mm Nut. Buts its been a while so i may be wrong.
The socket size for the axle shaft not, on a 2006 Chevrolet cobalt,is three-quarter inch. The socket should be a five-point socket.
30mm for the front. I think the rear are 24mm, but I usually use an adjustable for those.
The 2007 Nissan Murano takes a 26" drivers side, 18" passenger side and a fairly specialized 14" rear wiper that is difficult to find in the stores. See sources and related links below for more information. Since there are currently over 22 different wiper arm attachments, do not buy wipers just by …length only - be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment. (MORE)
The 2011 Nissan Murano takes a 26" drivers side, 16" passenger side and a fairly specialized 12" rear wiper that is difficult to find in the stores. See sources and related links below for more information. Since there are currently over 22 different wiper arm attachments, do not buy wipers just by …length only - be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment. (MORE)
the axle nut only holds the axle in the spindle. the rotor is held by the caliper and lug nuts when the wheel is on the car
If you're talking about the one in the back, it's a standard right-hand thread but thanks to repeated heating/cooling cycles the nut is on there TIGHT! You can't get it off with a regular wrench. There are a couple ways to do it. The cheapest way to do it is to get a "VW Axle Nut Tool." This is a p…iece of steel with a 1/2" square hole for your breaker bar on one end of it, and a 36mm, or 46mm if you're working on a Bus, hexagonal hole on the other end. You remove the cotter pin from the nut, put your breaker bar in the breaker bar hole, put the other hole on the nut you're trying to get off, then WITH THE TIRE STILL SITTING ON THE GROUND press down on the breaker bar with your left hand and beat on the axle nut tool, right above where the breaker bar is going into it, with a three-pound sledgehammer. This is guaranteed to get the nut off. If you do it all the time you'll ruin your bearings, but if you do it just once every couple of years it's okay. You can also use a 3/4" drive 36mm socket and breaker bar with a long cheater bar (when you do this you stand on the end of the wrench and bounce up and down until the nut gives up), a 3/4" drive impact wrench or any other way of generating a few hundred pounds of torque. (MORE)
185 to 260 ft lbs this is the front center nut that holds axle and front wheel bearing together not wheel lug nuts
Depends on the year and what size Ram. All 1994-2001 four wheel drive trucks used a 1 11/16 inch socket ot remove the front axle shaft nut. 2002-current 2500 and 3500 still use the same socket. 2002-current 1500 trucks use a 1 3/8
Not enough info to answer. Please reask the question and include the year, make, and model.
If you mean the nut that retains the CV axle, it is 1 and 3/16 and needs a long socket.