06 dodge 1500 crew cab the back speakers sound blown when you turn up the volume I have replaced them 2 times and still have the problem anyone know what could be causing this?
its not your speakers, its the radio
1 person found this useful
1. Drain Coolant2. Take fan clutch off3. Take fan shroud off4. Take the serp. belt5. Take the brace on the A/C and Alt. bracket6. Take the A/C compressor off the bracket (but do not recover freon)7. Take the idler pulley off8. Take the bracket off but leave the alt. attached to bracket9. Pull the wi…ring off the temp.gauge on the intake by the tstat housing10. Take the bypass hose clamps off by using a hose clamp pliers.11. Take the lower radiator hose off12. Take the bolts out of the water pump and take the pump off with a little tap with a hammer or pry it off.13. Clean off old gasket14. Install in reverse This done the same way as the v8 (MORE)
Remove the door and window handles tehn all of the screws you can find then the retainers on the sides and bottom of the door. The handles and retainers may require special tools available at the parts store.
1999 dodge durango dashlighttaillight failure at the same time when you turned the switch onI have no blown fusesWhat happened and what do you do to fix the problem?
Answer . \nIf multiple bulbs blew when you switched the lights on, there's most likely a short somewhere. The fuse might not be the properly rated fuse for that circuit, which could be why the bulbs blew before the fuse.
If you have a 93 Buick Regal and have replaced the turn signal flasher and the bulbs aren't blown then what else could be the problem of why they don't work?
The flasher is just for controlling the intermittent electrical current. There is also a fuse in the fuse block under the dash. . Answer . It could be in the switch on the column.
You have a 99 Dodge Ram 4x4 the power steering started to act up so you replaced the power steering pump twice However it still is hard to turn and pulses can anyone come up with what the problem?
Answer . \nIs the pressure in spec? Check for a possible restriction hydrolically if under. It may have nothing to do with the power steering system however. IF you get the front end off the ground, withe the wheels turns easly when you grab one side at the 3 & 9 o'clock position? IF tight, d…isconnect the tie rod ends and again try turning them to check for ball joint stiffness trouble. If tightness is gone, check back into the rack or tie rods, if you had a car, the strut bearing would be questionable also. (MORE)
Answer . \nAlright im going to anser this im not a mechanic but i know some what of a bit about sound systems alright first thing you need to do is go in and get the face plate off take a few srews out or even find some kid and pay him a small amount to do it take the speakers out put the new on…es in very self explanitory (MORE)
On Most GM vehichles, you can easily pry the door panel off with a flathead screwdriver. Remember, though, that the clips that you are prying off are very cheap, and usually break off. So, go to the GM dealership, and get a box of door panel clips before you pry off the panel. (a box of 25 costs abo…ut $10.00) Update... This procedure as mention above IE; "pry it off"on the 2005 GM Full Size Truck like was questioned about will DESTROY the door panel and cost you almost $450.00 to replace. The design on this truck to remove the door panel and ALL Silverados from 1999 up LIFT OFF in a UPWARD motion AFTER several screws and a plug type of fastener is removed Then and ONLY then may you LIFT OFF in a upward motion to remove the panel, do NOT do what the person said to do at the top of this Answer they do NOT know what they area talking about !!! Another update: I wouldn't say that the first person doesn't know what they are talking about. Most GM vehicles do have clips in which the doors can be pryed off. However, the second person is correct in this particular case. DO NOT PULL the panel off or try to pry the panel off. The panel must be lifted. On a 2006 Siverado, there are 3 7mm bolts. These bolts are under the lock, behind the door panel handle (not the door opening handle), and on the bottom of the door panel. Once these are off, remove the mirror cover and the cover behind the door opening handle. These cover can both be pryed off. Next, LIFT and PULL the door panel off. Finally, disconnect all wires and you're' good to go. (MORE)
1997 Dodge Ram 1500 4x4 replaced the headlight switch and the multi-function switch but my headlights still turn off randomly I usually have to turn the headlight switch off and on to get it back on?
Answer . I had this issue with my 97 dodge as well. When you changed the switch did you closely examine the wiring harness plug? Mine was damaged inside due to melting and it was causing a sporadic short. I had to cut the end and replace the connector. I also have heard of cases where the switch… shorting caused wires lower down in the harness to heat up and melt the casing causing shorts.. I also had this problem on a 1997. found out the same thing. the headlamp wire gets very hot. I got a whole kit with my switch and spliced the whole new multi-connector plug on the harness (MORE)
I'm in the middle of the process right now and it turns out to be a bigger ordeal than I had hoped for. I've only begun on the 3rd door side, but the steps for the other side appear to be simmilar just a bit more difficult in getting the panel off. The entire rear door panel needs to be snapped of a…fter unscrewing the two screws in the cup holder/ arm rest. The stock speaker will then be exposed and need to be pulled out, only after unsnapping the left side of the speaker mount. Unplug the speaker and you should be left with some speaker wire and a plastic connector. In order to connect the new speaker to the truck speaker wire, you must then cut the plastic connector off, leaving just wire. Following that, you then strip the wires, exposing the copper on all four ends and connect. Color coordination I'm yet to figure out. Cant tell which is neg or positive. You'll just have to test both or find out somewhere. And that's where I'm at. Looks like the next step will be drilling and mounting the speaker on the door frame. Hope this helped give you some sort of reference. (MORE)
What could cause a 1988 trooper to surge between 1500 and 2000 rpm the TPS has been replaced to no avail Problem persists?
Check for a vacuum leak. There is an idle compensator that could still be hooked up on your trooper. It is connected by a large diameter vacumme hose to a port directly below the carburetor visible from the passenger side ( vacumme routing sticker under hood shows it too). Plug it off at the intake …manifold and watch that intermittent vacumme leak disappear! (MORE)
99 Nissan Sentra was hit on front left and pushed over the curb have taken to be fixed twice but still hear a popping sound when making a U-turn or turn anyone know what problem is?
Answer . \nIf it only happens when turning then it has to be somewhere in the steering system. I would check for busted ball joints or tie rod ends. Also check the the steering wheel shaft hasn't broken somewhere. Check around the steering gear box to make sure the welds or mounts havent cracked…. It is possible that a short shaft has been damaged also. Hope this helps some. (MORE)
1989 XJ6 - Circuit One Failure Replaced fuse fan ac compressor and still get blown fuse wcircuit one failure occurring Anyone know why or how to fix?
fuses blow because their amperage is exceeded. you have a short somewhere, or the coil on the ac compressor is drawing too much current. DO NOT PUT A HIGHER RATED FUSE IN PLACE OF THE OLD ONE!!!!!!!!!!! that will cause more problems (such as a fire) is you have a wiring schematic, you can unplug all… items less one, and try that until the fuse blows. you can also try to splice in fuses (of the correct amperage) in various points in the circuit if the wiring is hard to trace. (MORE)
91Toyota4x4 I replaced starter and still have problems starting Doesn't happen everytime but once in a while I have to tap on starter while turning key to get it started. What else could cause this?
Answer . \nI tried that and it is difficult to turn the key and bang the starter too. This shouldn't be. I don't know if the soleniod relay is inside or on the starter or firewall - but your banging either makes it connect or makes the starter brushes connect to the armature. Next time this happ…ens and before banging on it - check the battery voltage supply to the starter and the battery supply to the solonid or starter relay post while your Buddy tries to crank it.\nIt mostly Sound like it is a bad replacement starter. It happens sometimes. (MORE)
Answer . Residue from the prior leak, cracked the neck when installed, defective core. Any leaks on engine side of firewall leaking in somehow??
Honda Man's Answer . Providing it was a faulty fuel pump to begin with, you may have a new defective fuel pump now. Another possibility is that one of the fuel lines is kinked and restricting the flow of fuel. Check the fuel pressure with key on engine off and while in the start position. You may… also try spraying starting fluid in the air intake momentarily to verify it is a fuel related problem. (MORE)
My 95 Chevy Blazer is acting like it's not getting gas stalled out and won't start back up anyone know what the problem could be?
Answer . the fuel pump is probaly bad. Need to run a fuel pump pressure test, and check fuel pump relay, check fuel pump fuse on passanger side fire wall. Only if you have no fuel pressure, gauge should read 9 to 13 LBS of preassure.
How do you repair speaker sound that's very low when the volume is turned all the way up after you have replaced the old speakers with new speakers in a 1993 Ford Thunderbird LX?
The best way would be to unsolder the old speakers and resolder the new ones on.. The easiest way would be to cut the wires right on the edge of the solder, strip the wires, twist the copper, and loop them through the holes on the new speakers. This isn't the most recommended way to connect speaker…s because they can come loose over time and you may have fidelity loss.. Another way could be solderless connetions, but to do this need the little connectors and crimping pliers to attach them to the wires. Basically you will spend more money with this option than with a new soldering iron and a coil of solder. This option also has the possibility of coming loose over time and minimal fidelity. (MORE)
for an exact answer, you can go to crutchfiled.com and it will allow you to look up specific sizes for any year,model, etc. what i have found for my dodge truck is 6x9 for the fronts.
child locks check owners manual for location of override switch... open front door look for switch on a or b piller
There is no actual fuel filter on your truck, the pick-up in the gas tank acts as the fuel filter, another bright idea from the manufacturer.
Can installing a snow plow wire harness on a 91 Chevy crew cab pick up cause a problem with the marker lights and radio or is the radio the problem or fuses between the two?
A pinched or crossed wire for a 91 Chevy crew cab plow could causethe lights and radio to not work. They could also be separateproblems. Start but checking the marker lights fuse, then recheckall of the snowplow wiring.
Lights only work when you hold the brights lever back anyone know whats the problem or how to fix of a 1993 dodge Dakota?
There are two circuits at the multifunction switch lever. One is for the flash to pass. The other is the normal high/low beam circuit. The two most likely problems are a lack of power from the headlight switch, or a broken wire at the multifunction switch connector. The second is prone to happening …if you tilt the wheel frequently. (MORE)
The best thing to do would probably be to just buy a repair book like haynes from your local parts store it will have step by step instructions and pictures to help. You'll need a couple speciality tools but nothing too expensive.
Mitsubishi eclipse 2001 sraio speakers dont work replaced radio but still no sound from speakers you dont think all 7 speakers blew out What could the problem be?
I went through this whole problem when I changed out a failed factory infinity system for an after market. The problem is that the speakers all run of the factory power amp which is probably not wired by your new radio. try this sight : www. scosche .com/products/sfID1/151/sfID2/158 but make sure yo…u get the wiring harness that has the round connection that powers the amp. When I ordered on-line I did not order the right harness so I sugest that you call and talk to support adviser who will make sure you get the right one. hope this helps. (MORE)
first.. you will probably need to remove the back seat just to make it easier second.. you will need a torquex head to remove the seat belt bolt and then you will need a Phillips head to remove the kick panels screws theres a few of them third.. you must unscrew the stock speaker, 4 screws for…th. after unmounting the speaker you will need to unplug the wiring harness, it will be mounted inside the body panel for convience. fifth. either order speakers from crutchfield and they will give you new plug in's that will fit to your new speakers or cut the wires and splice in the green and black wire.. green=positive, black=negative (MORE)
For a 1998 Dodge Ram 1500 extended cab, there are two differentsizes of speakers. The front speakers are 6x9 and the rear are5-1/4.
What will cause a 1990 Cadillac Deville to back fire when you turn on headlights or any accessery I have replaced Battery Alt still runs rough and backfires at times?
Not sure about the relationship to the headlights, but I've had the same problem for years. After replacing relays, plugs, wires, distributor cap,.......... with no success I almost gave up. But then, a great mechanic came along and found it was the computer that was bad. $400 later my car runs real…ly well. Good luck. (MORE)
The front door speakers in the 2001 Silverado 1500 HD Crew Cabmeasure 6 3/4 inches. The rear side panel speakers measure 4 inchesby 6 inches.
Remove the switches and a couple screws that hold the door panel on. then pry the push in door clips that hold the door panel in place out. take the screws out of the old speaker and cut off the pigtail attached to it. solder and shrink wrap or crimp on the new wire connectors that came with the spe…akers and re-install. (MORE)
12 m.P.h and up for some reason they dont work on 2007 dodge ram trucks
Short Box (Lt. Duty) 98 L (26 gal.)* Long Box (Lt. Duty) 132 L (35 gal.)*
Not sure, but it sounds like a weak fuel pump or clogged fuel filter . If the fuel pump is located in the tank, gas could be sloshing around on turns and inclines a weak fuel pump would have a hard time picking the fuel up. hope this help
I own a 1995 dodge ram 1500 360 motor problem is it wont rev past 2000rpm ECU cap roto o2sensor EGR all replaced and no vacuum leaks what could be the problem still?
fixed problem after afew times double checking everything .. it was a blocked catalytic converter
as long as the tires are proper ply and in good condition, yes you can carry 1500 lbs.
You have water in your passenger side floor board only when it rains you have a 1998 dodge Dakota sport ext cab does anyone know what could be causing this to happen?
I also have a a 98 dodge Dakota sport that the passenger side floor board and carpet was getting soaked with water...but only when it rained. I removed the seats and carpet hosed it down with the garden hose and found a leak at the passenger rear side window...vent window, however it was only visibl…e after removing the side trim below the window. After taking care of that leak the problem persisted. I finally located the leak on the cab wall about 8-10 inches below the window and almost directly behind the passenger seat. It looks like it is coming in at a cab weld...not sure yet but definitely the source of the problem....going to try spray rubber sealant called flex seal sold at rural king (MORE)
You can go towww.crutchfield.com the have a program link that will tell you what the factory sizes for your vehicle. And the brands that make direct fit speakers. And it's FREE.
Either you tire is rubbing or if its a front wheel drive it could be you "CV" axle's... Other than that i don't know i hope that helps?
When i start my 2004 dodge ram 1500 the airbag light go's out and comes back on and then sounds bing ones What is up with that?
The light comes back on when the computer detects a malfunction and sets a code. You will need to have the system diagnosed by a qualified technician.
The 2009-2010 Dodge Ram Series 1500 Pickups take 22" replacement windshield wiper blades on both sides front. Note however, when buying wipers be sure to always lookup your vehicle make, model and year in the application guide book at the store, or now-a-days you can Google 'lookup wiper size'.
place jack under vehicle just to the rear of the front tire's. Jack vehicle up using the frame of the vehicle. *Important* place jack stands under vehicle. I place them under the lower control arm's or on the frame (be sure to use stands that will support the weight of your vehicle). if unsure of th…e weight, there should be a vehicle identification tag on the driver's door jam that will tell you GVW (gross vehicle weight) on most vehicles. In the rear (if rear wheel drive) jack vehicle up by using the rear differential. When looking under the vehicle it will be the mass of iron centerly located between the rear tires. Again *Important* Use jack stands to support load of vehicle. place jack stands on the rear axle tube's and there u go!! (MORE)
brake pads right wich means is has calipers, remove tire, take of the two bolts holding the caliper to the mount, pull out brake pads then using a c clame press back the piston all the way put in new pads and put back together.
Why does my 96 Mitsubishi galant turn off on me when im hitting brake i would have to drive it with 2 feet so it wont turn off but it still does.Does anyone know whats the problem with the car?
This car has a serious engine problem and needs to be diagnosed by a knowledgeable person. There is no way to know the correct answer with out inspecting it in person.
If your car speakers have a static sound as if there blown but they're brand new and look fine what could the problem be?
Easiest common sense things first you should check and make sure that everything is wired correctly and then if that doesnt fix it you could check and make sure that power wires arent causing interfearance or something like that. sometimes sound systems act really wierd with power cables and input c…ables close together, after you've done all that if it still isn't fixed best bet unfortunately is taking them back for one, or getting them checked by a professional (MORE)
After turning the volume all the way up on your speakers you still cannot hear any sound what is the next step?
Did you.. - plug it in ? - hook up the power ? - on what device are you using those speakers ? - Is it ON ? _ If its a computer .. Is the sound card detected ?
Yes, if the timing was not set properly when replacing the belt then the exhaust valves open at the wrong point in the cycle. This will cause the catalytic converter to be dealing with gasses that are outside of the normal parameters. Either unburnt hydrocarbons or the valve opening before combustio…n is completed, either way it will get very hot, and potentially melt the innards and potentially plug the exhaust. The timing mishap can be due to the cams moving when you removed the old belt, or the new belt not being put on in the right order so the slack ends up at the idler pulley. (MORE)
Will music sound better if you turn up the volume on with the knob on the speakers or with your computers volume control?
i think maybe its the same, but the volume control think i control the intensity of the volume but the knob of your speakers turn up the volume, well the conclusion is that the both things a good solution.. 50/50
What could be the problem if you have replaced your fuel pump three times and its still running poorly?
Tha may be fuel filter from fuel pump or fuel filter outside of gas tank or the car injectors
Leaking heater core, debris in the HVAC box, oil leak under hood, etc Leaking heater core, debris in the HVAC box, oil leak under hood, etc
Check engine light and an improper reading in the overhead console. Check engine light and an improper reading in the overhead console.
Press the rocker switch on the right side. If the volume graph is already at full, that's as loud as its going to get. Note that content like YouTube videos may play very softly if the video was uploaded with a low audio volume.