01 dodge ram 2500 ctd overhead console displays letters ccd what is this?
It means you have a problem with the CCD Bus in your truck. I believe that is related to the signal from the Body Control Module (BCM). I would suggest checking your wiring connections and make sure they are tight.
5 people found this useful
1999 ram 2500 outside temp in overhead console reads erratic temps like 320 for outside temp then drops to 3 what gives?
I have discovered that my Ram 2500 inside temp guage is somehow tangled up with the compass. when I turn in any direction the temp. changes I guess it has to go to the dealer!I am one of the 3 who have this problem. just press and hold both buttons in like you are resetting the economy! I had the s…ame problem. figured it out on a road trip. same goes to get it back. Check to see if you are reading the compass. Mine had me going for a while before I figured out that it was reading heading degrees not temperature degrees. The resetting process can change it between the two types of readout. (MORE)
I figured it out. Upclip the two clips closest to the windshield and move console back toward the read of the cap. There are two L shaped hooks at the read the hook into the top of the cab.
In the 1997 Dodge Ram 1500 the overhead console which has the direction and temp the temp displays OC what does that mean and how do you fix it?
It means that the circuit is open that goes to the temp sensor by the grill. Either the wires are broke or the sensor is bad.
You probably have a short in your steering wheel column. As an owner of a very small (six) fleet of Dodge pickup's (1500's & 2500's) I have experienced this problem in 3 of them. Two were corrected by removing and cleaning the inter-bus connector located inside the engine compartment fuse distri…bution center. It is located on the right rear of the center than can be viewed (standing at the drivers side looking into the engine compartment), and held in place by a phillips drive screw. A special note: the retaining screw appears to be threaded into a nylon (Teflon?) retainer that must not be overtightened. This one, I'm still looking for a solution. The third we are still working on, and are investigating chaffed wiring as a possible cause. (MORE)
1999 Dodge Ram - How do you remove the trip computer - overhead console there aren't any screws or areas to pop it out?
Answer . From what i have heard there is a couple clips towards the front of the console. after they are removed you can slide the entire console back to release the hooks securing it to the ceiling.
Open the garage door opener compartment and remove the screw located at the top, once removed open the glass storage compartment and push in the latch located on the side closest to the garage door compartment. Once you release this tab the unit will come down, remove the two plugs and lift off the …hooks. This is for a 2008 CaravanSE: (not at all like the model described above) The little compartment that holds the sunglasses/conversation mirror popped out of place recently. To fix it, I needed to remove the console that holds the bin and the two courtesy lights. My wife's van does not have the power tailgate/garage door opener optional switches in the console. There are no screws of any sort visible! Really had me baffled. I went to "JustAnswer.com" It cost me $38 for the following hint: "Use a special trim removal tool #XYZ to gently pry the two front corners near the windshield, between the console and the headliner..." I used a broad, flat screwdriver, worked okay. This will release the front two of the four "one way" clips and the front edge will come down ...then tug firmly at the rear corners to pop the rear clips free...it takes quite a bit of force. Once all four pins/clips are free, undo the two headers that connect the courtesy/map lights. To re-install, I gently worked the clips out of their sockets in the ceiling of the van and re-installed them on the flat posts of the console. Re-connect the lights and replace the foam tape that holds their wiring in place (I presume to stop rattling) Close all doors of the van, wait for the lights to go out. Line up the four tabs with their sockets. Whack each corner with your fist to seat the clips. (If you do this with the lights on, you'll probably break the filaments of the map light bulbs as you whack the console). (MORE)
Answer . Is this a pickup or a van? The last Dodge pickup I had to change the evaporator on was a 2000, so maybe it's the same. 1-Evacuate the system. 2-Pull the A-Pillars off. These are in front of the driver's and passenger's side windows. Disconnect any electrical connectors. 3-Rem…ove the kick panels. These are down low forward of the front doors. Disconnect any electrical connectors. 4-Remove the center console, if equipped. Disconnect any electrical connectors. 5-Disconnect wiring connector from blower motor. If there's a green and/or red wire at this connector, push the terminal out of the connector and cut any tape along that wire(s) that you can see. 6-Clamp off and remove heater hoses at connection near firewall (underhood.) 7-Disconnect AC line quick connects near firewall underhood. 8-Remove the 6 to 8 dashboard mounting bolts that are exposed after removing kick panels and center console. 9-Tile dashboard back and remove from vehicle. Two people are required, unles you want to rip upholstery. 10-Remove 5 fasteners on underhood side and three fasteners on interior side holding the HVAC case to the firewall. 11-Disconnect electrical connectors as needed. 12-Remove case from vehicle. 13-Remove several screws. 14-Split halves of case. 15-Pull the core out. Note that if you purchased a non-Mopar core, it doesn't look quite like the one you just pulled out of your truck and won't fit in the same place. (MORE)
Reset? I guess you could just unplug it behind the left A-pillar trim panel. The trim panel is held on with retainer clips, so you just pull it off.
Disconnect neg battery cable. recover r134 AC freon.(it may be unlawfull to release this into the atmosphere) disconnect AC lines in engine compartment at firewall. remove AC condensor remove PCM module from fire wall but do not disconnect the cables from it. Disconnect two heater core hoses from fi…rewall. note hose clamp position prior to doing this step. remove panel under steering column(2 screws) disconnect cables at left of driver under dash. disconnect pneumatic lines to right of driver under dash. remove brake release rod from brake release pull lever. remove hood lever (2 screws). remove 2 steering column nuts and lower steering column onto driver seat. make sure steering column is in locked position with front wheels aligned straight ahead. remove brake light switch from steering column. remove screws holding down drink holder on center tunnel. disconnect air bag cable from center tunnel bracket connector. remove 2 10mm screws from center bracket under dash. remove driver side cowel panel under dash exposing 13mm bolt. remove passenger side cowel panel under dash exposing 13mm bolt. loosen both 13mm bolts to allow entire dash assembly to be raised. remove 5 10mm screws at top front of dash panel near windshield. open glove box door, pull on rear of box to allow door stops to pass through dash at each end of door. lift glove box out of hinge and set aside. disconnect heater fan plug and ac/heater module cable behind glovebox. unless i missed something the entire dash assembly can be pulled rearward slightly , then raised up partially onto front seats. you can secure assmbly in the raised position with a rope or bungee cord. the ac/heater module is now accessible which has the heater core mounted in it. from inside cab find and remove 3 nuts securing ac/heater module to firewall note ground wire position on heater core bracket. from inside engine compartment remove 4 nuts at firewall that secure ac/heater module to firewall. once all nuts are removed pull ac/heater module rearward from firewall and then out the passenger side door. remove the bad heater core. rinse all spilled coolant from ac/heater module with water and allow to completely dry before re-installing. install new heater core into ac/heater module. reverse the ac/heater removal procedure to install module and dash assmbly back to starting positions. this job can be a pain. take frequent breaks and do not rush or you will break things. if possible work with a helper. good luck (MORE)
remove the two light lens be careful not to break them. then remove the two torx screws behind the lens. give a slight pull down on the front of the console to remove the two clips and you are done.
The 1999 Dodge Durango overhead console wiring connections arebeneath the overhead console. You will need to remove the overheadconsole?Ã¦in order to access the wiring connections.
most likely your engine lite is on if it is speed sensors your control module will give you codes you should have speed sensor in differental and one at axle going through same deal on 95 ram 4x4
The ABS is your anti lock brake system. It has it's own ecm that moniters your brake system. The light can come on for many reasons. First thing to do is check the sensors. They are bad about getting debris on them. Remove the wheels and clean them off. You can locate them by following the wires clo…se to the wheels. After that, remove the battery cable and try to reset the system. If the light comes back on, have it checked by a professional.. You need to have the system checked for codes. You can then fix the cause of the code and that will fix the light. (MORE)
Adjust the display to show Avg MPG then press & hold both buttons until display reads 0 (zero). Takes about the count of 3.
The flowchart in isolating and diagnosing the condition istwo-fold. First, all relays and fuses aspect to this circuit shouldbe inspected for blowing or shorts. Second, the screen can bepulled and its harness tested for a current via a meter.
First remove the door panel. Once you have the door panel off you will be able to see the Allen screw that secures to the bottom of the swivel arm. It's easy to get to. The only thing is that once you have to tighten it once, there will be a second and a third time. So what I did is pulled the Allen… screw out and put some lock tight up in there and that was the last time I had to mess with it. (MORE)
To remove the overhead console you will first need to disconnectand isolate the negative battery cable. Remove the overhead screwsand pull straight down on the console.
Assuming the fuse box is the same as a 98, it should be located in cavity 12. That the same row as the airbags with the yellow covers, cavity 12 is is the far left of this row and it should have a black cover on it. I assume this is to keep it in place in case of an accident as I believe the seat be…lt pretensions are on this fuse. For some extra info, items listed on this fuse for my 98 is as follows radio, underhood light, done lamp, cargo light, glove box light, power mirrors, diagnostic connector, ignition halo (ignition key hole light), visor and SCTM (seatbelt pre tensoner) Hope that helps (MORE)
Outside temperature displays 130 degrees on the Dodge PU overhead console and the compass works fine?
More than likely the sensor has either been moved or has fallen off. The sensor should be on the driver side front of the radiator, lower left side. More than likely you have had either frontend body work or radiator work done and the shop in hooked it and never bolted it back down. There are two p…ower sources for the console - one switched power and one directly to power (non-switched). You have to connect the non-switched power to the unit before you connect the switched power. Once the power is connected in the right sequence, the unit works correctly. (MORE)
you have to open the glove box and remove the screw on the left and the screw on the hook by the glove box then every thing else snaps out.
My 1999 ram 2500 quad cab short bed with a 1/4 tank of gas weighsabout 6200 lbs. My 2001 Dodge Ram 2500 5.9L diesel according to the VIN report is5,501 lbs. The GVW is 8800 lbs. so I can theoretically haul 3300lbs. or 1.5 tons including passengers, fuel etc. Said weight iswith Snowplow, towing packa…ges and 5 3/4" factory lift kit. (MORE)
It is under the dash on the passenger side of the car. You can access it without removing any other objects.
I googled "04 Dodge Ram Manual" and downloaded the service manual from one of the links, which is different than the owners manual. The service manual is 2000+ pages long....here's what is says about the overhead console removal procedure.... . REMOVAL . OVERHEAD CONSOLE REMOVAL . (1) Disconnect… and isolate the negative battery. cable.. (2) Remove the overhead console retaining screws,. located in the sunglass storage bin.. (3) Using your fingertips, grasp the sides of the. overhead console and pull straight down evenly to. disengage the two snap clips at the front of the unit.. (4) Lower the overhead console far enough to. access the wire harness connectors.. (5) Disconnect the EVIC, CMTC electronic module. and the reading/courtesy lamps electrical connectors.. (6) Remove the overhead console from the vehicle.. INSTALLATION . (1) Position the overhead console in the vehicle.. (2) Connect the EVIC, CMTC electronic module. and the reading/courtesy lamps electrical connectors.. (3) Grasp the sides of the overhead console and. push straight up evenly to engage the two snap clips. at the rear of the unit.. (4) Install the overhead console retaining screw,. located in the front of console. Torque the screw to. 1.2 NÂ·m (10 in. lbs.).. (5) Connect the negative battery cable.. I googled "04 Dodge Ram Manual" and downloaded the service manual from one of the links, which is different than the owners manual. The service manual is 2000+ pages long....here's what is says about the overhead console removal procedure.... . REMOVAL . OVERHEAD CONSOLE REMOVAL . (1) Disconnect and isolate the negative battery. cable.. (2) Remove the overhead console retaining screws,. located in the sunglass storage bin.. (3) Using your fingertips, grasp the sides of the. overhead console and pull straight down evenly to. disengage the two snap clips at the front of the unit.. (4) Lower the overhead console far enough to. access the wire harness connectors.. (5) Disconnect the EVIC, CMTC electronic module. and the reading/courtesy lamps electrical connectors.. (6) Remove the overhead console from the vehicle.. INSTALLATION . (1) Position the overhead console in the vehicle.. (2) Connect the EVIC, CMTC electronic module. and the reading/courtesy lamps electrical connectors.. (3) Grasp the sides of the overhead console and. push straight up evenly to engage the two snap clips. at the rear of the unit.. (4) Install the overhead console retaining screw,. located in the front of console. Torque the screw to. 1.2 NÂ·m (10 in. lbs.).. (5) Connect the negative battery cable. (MORE)
I assume you must have a diesel if you want to know where the vacumme pump is. In that case it is in front of your power sterring pump. Your power sterring pump bolts to it.
I think you mean pdc. That is the power distribution center. The underhood fuse box.
\nP0601 - PCM Internal Fault Internal Controller Failure. Take the vehicle to a dealer as this may be covered under the emissions warranty.
Overhead console LED display on your 1994 Dodge Intrepid is dead Any idea as to what may be wrong and estimate on cost to repair?
I have a 95 Dodge Intrepid that has the same problem. On my Dodge The circuit board is fried. Capacitors, diode and tracing burned off board. If you don't have any blown fuses. Then yours could also be fried. I Checked with the local dealer and they want $691 just for the part. https://www.trademoti…on.com wants $486 for it. Or you could visit your local juck yard and find one. any 93-96 Intrepid, LHS or Concorde should work, according to the dealer. (MORE)
An overhead console is a storage area on the ceiling of the vehicle just above the windshield either between the visors or down the middle between the seats. It typically holds sunglasses, remotes for garage door openers, map or CD storage, and possibly the compass/exterior temp display.
There is a phillip head screw in the front of console. Remove that first. They slid a flat screw driver in along where it meets headliner and pry down. There are 4 clips holding it to roof. Then unplug electrical connector. That's it.
The holder replacement will depend on the model of the Dodgevehicle. Most of the holders have small pins on the sides that theyhinge on. Bending the sides in gently should release the pins fromthe pin holes, allowing removal and replacement.
Under vehicle, center, below cargo area, mounted on top of fuel tank, in fuel pump module.
Gas engine, it is inside the fuel tank, part of the pump module. Diesel, it is on the driver side of the block
This means the truck is a 3/4 ton pickup (a heavier duty truck), whereas, the 1500 is a lighter - 1/2 ton pickup.
Where are the 3 bolts or screws you need to remove to open the center console so you can change the air filter on a 1997 Dodge Ram Van 2500?
center console? air filter would be under the hood. do you mean cabin filter? No. I mean air filter. This is a Van, not a truck. Lift up the edges of the carpet around the center console and you will see the screws.
under the rotor in the distributor unplug the wires take off the rotor and pull it out
A 1995 2500 could have a 5.9L V8, a 8.0L V10, or the 5.9L Cummins diesel.
Remove the door panel, then the wire harnesses, then pop out the master switch. The door panel removal: Remove the door handle with a star driver, then remove the three Phillips screws holding the panel in place. Next lift the panel up over the door latch. Before pulling the door panel away, unlock… and remove the wire harness connectors from the master switch. Turn the panel over, and pop out the master switch, being careful not to snap of the one way clips that hold it in. I saw master switch replacements on EBay between $50 and $100 or you can try the junk yard. (MORE)
13.5 I just clocked my 1996 and the last tank I got 19.6 and that was a good mix of city, freeway and trailer pulling.
there is no tach sensor. it is my understanding that the tach iscontrolled by 2 sensors. The first is the TPS(Throttle positionsensor) which is located on the drivers side under the fuel pump,it has 3 wires a purple which is a 5 volt send wire, a ground wireand a return signal wire. these can be tes…ted but I have not foundthe plug yet to test the resistance in the wiring harness. Thesecond sensor as I understand is the camshaft position sensor, Ihave yet to find this one and test it on my truck. I did the selfdiagnosis on the cluster by pressing the reset button on the dashand holding it and turning on the ignition till all lights light upthe releasing it, the gauges will preform a self test and on minethe tach did nothing, given this info I am concluding that my tachis bad and not the cluster cause all the other gauges testedaccording to specs as outlined by dodge. I have extensive knowledgeon this truck as I own a 2006 dodge ram 2500 larime equipped withmonster intake a superchip 4' exhaust and a upgraded ECM. (MORE)
Dodge Ram 2500 car parts are compataible with dodge ram 2500. this way you know they are compatible and don't have to worry if something will not work
This depends on what you would like your brand new Dodge Ram 2500 equipped with. Talking with the local Dodge dealership in your area can give you a quote on this new vehicle.
According to preliminary towing and hauling figures the towing capacity of a dodge ram is 5,500 pounds on diesel 4x4 pickups and 5,000 pounds on diesel 4x2 pickups
The Dodge Ram 2500 will get under 20 mpg. Actual miles per gallon will vary depending on tires, what you are hauling, whether you are driving on the highway or small roads, etc.
I don't believe that it was an option until the 2009 model year. I don't believe that it was an option until the 2009 model year.
The frames, axles, springs are all different. So you would have to change everything but the body. The frames, axles, springs are all different. So you would have to change everything but the body.
Well if you can drive around for 15 to 30 min and you battery is still dead then your alternator is bad or if you put a new battery in and it go's dead avry time you run the truck then your alternator is bad
Not enoug info to answer, please ask a more specific question. Not enoug info to answer, please ask a more specific question.
A gasoline engine makes it's own vacuum. The diesel engine has a vacuum pump next to the power steering pump. A gasoline engine makes it's own vacuum. The diesel engine has a vacuum pump next to the power steering pump.
It was available with the 5.9L v8 gas, the 8.0L V10 gas, and the 5.9L inline 6 Cummins diesel.
It will fit in any 2500 or 3500 Ram. If it is a different versionof the Cummins it will take a lot of modifications to make it work.